Deutsche Version

Example: Multiple parallel processes in a job chain

The goal:

• Write a job chain that starts with the job named "truncate_export_table".
• After this job has been completed four jobs named "table partition" are to be run executed in parallel.
• A single job that indexes the new partition tables is then to run.
• Finally, a further four jobs that test the partition tables are to start in parallel.
  This job chain is shown schematically in the diagram in the "Diamond" section  section below.

Writing the job chain

The following steps have to be followed to achieve a job chain that meets the requirements listed above:

1. A "splitter" job has to be included for each "set" of job nodes that are to be carried out processed in parallel. The splitter job starts the parallel jobs as soon as it itself is started.
2. In order to do this the splitter job has to "know" the names of the parallel nodes, which are specified in the splitter job's state_names parameter . - !! to be done !! - : link to Node Parameter Definition wiki-artikel(see How to set and read job and order parameters).
3. The parallel processing normally ends at a specific node in the the chain: thereafter processing continues serially. This node is the synchronisation synchronization node and implemented using the Sync-Job.

...

Diamond

...

Diagram

The example job chain will look like this (diagram generated with the Sandbox JOE Version):

Image RemovedImage Added

We refer to the pattern that results with this type of job chain as a "diamond" pattern. These diamonds can occur more than once in a job chain: both sequentially, as shown in the diagram above, in parallel and nested. They can also be combined with other job chain patterns such as emerald or cross-over patterns (see Example showing the synchronization of multiple job chains).

Job chain list view

The next illustration shows a list view of the job chain as produced by JOE:

Image RemovedImage Added

The "Splitter" job

A generic splitter job is delivered with the JobScheduler JITL jobsJobs. This job can be found in the "./live/sos/jitl" directory.

We recommend that you use the following syntax for the names of job nodes that are processed in parallel:

• "splitter job node name" ":" "job name" - in . In the example diagram above, one of the first nodes would be then have the name split_partitions:partition_1.
  This syntax allows the diagram algorithmus algorithm in JOE (that was used to draw the "diamond" diagram shown above) to know and to correctly display the nodes that directly follow on from the splitter. This is because the JobScheduler syntax does not recognise It is necessary to use this type of job name syntax as the syntax used by JobScheduler does not recognize predecessor relationships (only successors).

The use of the above syntax is not necessary for the correct functioning of the JobScheduler.

Splitter job parameters

...

See documentation of job JobChainSplitter.

The state_names parameter

• The splitter job state_names parameter is used to specify the node names of the jobs that are to be started in parallel (see Setting_ How to set and read job and order parameters).
• The node names are to be seperated separated by semi-colons.
• In job chains with this diamond pattern structure, the parameters are specified for the job chain and referred to as node parameters. Node parameters can be used to specify parameters for more than one splitter in a job chain, independently of one another, as in our example, without creating conflicts.

The parameters for the split_partitions splitter job - as shown in JOE - are:

Image RemovedImage Added

The "Sync" job

A unique sync job is required at the end of every set of processes running in parallel (see - !! to be done !! - Setting_up_a_sync_ Example showing how to set up a sync job), when further nodes in the job chain after the sync node are only to be processed after all the jobs (tasks) that are to be carried out in parallel have been completed without errors.
Each sync job has to be unique within a JobScheduler instance - and within a job chain as long as a - !! to be done !! - cross-over pattern has not been implemented (see Example showing the synchronization of multiple job chains).

For more information see the documentation for the JobSchedulerSynchronizeJobChains job.

Best

...

Practice

Start- und End-Knoten verwenden

Use "Start" and "End" nodes:

We recommend that you use our Wir empfehlen, in jeder Jobkette im ersten Knoten den Startjob /sos/jitl/JobChainStart und im letzten Knoten den Endjob start job as the first node in every job chain and our /sos/jitl/JobChainEnd zu verwenden.

Eindeutiger Name für Sync-Job

Um den Sync-Job eindeutig zu definieren empfehlen wir, den Namen der Jobkette, in welcher der Sync-Job verwendet wird, als Präfix in dem Job-Namen des Sync-Jobs zu verwenden.

...

end job as the last full node.

Assign each sync job a unique name:

Assign each sync job a unique name by using the name of the job chain in which the sync job is included as a prefix in the name of the sync job.

• For example: ideal_insert_to_export_table_parallel.

...

• sync_partitions

Follow our convention for node naming:

Splitter Nodes

We recommend that you use the following syntax for the names of job nodes that are processed in parallel:

• "splitter job node name" ":" "job name". In the example diagram above, one of the first nodes would then have the name split_partitions:partition_1.
  This syntax allows the diagram algorithm in JOE to draw job chain diagrams and correctly display the nodes that directly follow on from the splitter. It is necessary to use this type of job name syntax for the algorithm as the syntax used by JobScheduler does not recognize predecessor relationships (only successors).

Parallel Nodes

We recommend that you use the following syntax for the names of job nodes that are processed in parallel:
"splitter job node name" ":" "job name".

In the example described above, one of the first nodes would then be split_partitions:export_table_partition_1.
This allows the diagram algorithms in JOE to know and correctly display the nodes that directly follow on from the splitter. This is because the JobScheduler syntax does not recognize predecessor relationships (only successors).

Job Nodes

As far as possible, the names of job nodes should be identical to the job names (poss. without the folder name). If a job is used more than once in a job chain, then the node name can be uniquely specified using a letter or number as a suffix.

Error Nodes

The name of the error node should either contain the job name or be identical with it. This means that in the event of an processing error in the job chain, it is possible to see immediately in JOC the point in the job chain where the abnormal termination occurred.
In addition, the name should start with an "!" (an exclamation point, or with another unique special character). This makes it easier to see in the order history in JOC that the job chain has terminated abnormally.

See also:

• JobSchedulerSynchronizeJobChains.
• Examples for using Sync-Jobs see Examples - Jobs, Job Chains and Orders

Downloads

You can download the example described in this FAQ :

Konventionen für Knoten-Namen

Splitter-Knoten

Wir empfehlen, den Knoten-Namen eines Splitter-Jobs mit der Zeichenfolge split zu beginnen, zum Beispiel split_partitions. Damit "weiß" der Algorithmus, der das Diagramm erstellt, dass es sich um einen Splitter-Knoten handelt und kann ihn korrekt darstellen. Den Knote-Typ "Splitter" gibt es in der Syntax der Job-Knoten nicht.

Parallele Knoten

Für die Knoten-Namen der parallel zu verarbeitenden Jobs empfehlen wir die Syntax "Knoten-Name des Splitter-Jobs" ":" "Name des Jobs", zum Beispiel split_partitions:partition_1. Damit "weiß" der Diagramm-Algorithmus, welche Knoten die direkten Nachfolger, aka Vorgänger, des Splitters sind und kann dies korrekt darstellen. Die Syntax des JobScheduler kennt eine Vorgänger Beziehung nicht, deshalb die hilfsweise Darstellung über den Knoten-Namen.

Job-Knoten

Soweit möglich sollte der Name des Job-Knotens identisch sein mit dem Job-Namen (evtl. ohne Folder Namen). Wird ein Job mehrfach in einer Job-Kette verwendet, so können die Knoten-Namen durch eine angehängte Ziffer (oder Nummer) eindeutig spezifiziert werden.

Fehler-Knoten

Der Name des Fehler-Knotens sollte den Job-Namen enthalten oder identisch sein mit diesem. Damit kann bei einem Fehler im Ablauf der Jobkette sofort in JOC erkannt werden, an welcher Stelle die Jobkette abnormal beendet wurde.
Außerdem sollte der Name mit einem "!" (Ausrufezeichen, oder mit einem anderen eindeutigen Sonderzeichen) begonnen werden. Damit kann in JOC auf dem ersten Blick in der Order-Historie erkannt werden, daß die Job-Kette abnormal beendet wurde.

siehe auch

Downloads

Das verwendete Beispiel können Sie hier herunterladen insert_to_export_table_parallel.zip.